Getting from here to there on camp property shouldn’t be the biggest obstacle or most memorable moment for any visitor. But just because there aren’t any “moving parts,” one shouldn’t assume that there isn’t more than meets the eye to a good roadway system. The horizontal route, the steepness, the drainage, and the surface itself all should work together to provide a safe means of moving about. If your facility doesn’t have the luxury of rebuilding its roads every year (or even every other year!), read on and see what you can do to get the most out of your roadway investments.
For the most part, camps and conference centers are largely “stuck” with the route their roads take since they are already in place. In order to better understand how your roads are serving you, we should look at these design components. Overall, the physical shape of the roadway path (called vertical and horizontal alignments) will dictate the sight distance along the path. Sharp turns and steep hills prevent vehicle operators from seeing and anticipating roadway obstacles — particularly intermittent ones like pedestrians or wildlife. This is especially true at night since headlights only travel in straight lines directly aligned with the vehicle. In short, if campers and vehicles are expected to share the same routes, the cost of constructing improved footpaths that establish specific crossing points is money and time well spent.
Notice the words “constructing” and “improved.” This doesn’t necessarily mean paved highways, but the paths should be planned, built, and maintained for foot travel. Their construction should be pursued in much the same manner and with the same conviction as roadway construction — with a layout, design, and commitment of money, labor, and equipment — if the finished paths are to be used as an alternative to walking on the road. No matter how “back to nature” your campers may be, if the footpath is always sloppy with mud, uneven, or laden with trip hazards like stumps and rocks, the road will be the route of preference.
For new site development, or where old roads are being reworked, the sight distance and operational issues can be reasonably addressed in design and construction. There are design standards for rural roadways, which set limits on the steepness and sharpness of curves — and these should comprise the foundation of the design.
Imagine looking down on the site from above. The road should have as broad, sweeping curves as the site will allow. The “insides” of each curve should be cleared to allow headlights to illuminate the road across the open area to allow the driver and pedestrians time to adjust for each other. Curves which break one way and then the other in short succession makes for difficult driving, particularly for trailered vehicles.
Now imagine the roadway as you might see it across the edge of a cliff or cut away.The profile looks a little like a smooth line graph. Hilltops (crests) should be broadened to allow the maximum distance for headlights to light the path. The bottoms of curves (sags) will tend to collect water runoff. These will flood and deteriorate most rapidly unless adequate provisions are made to pass the water from the high to the low side of the roadway.
Most rural roadways are best suited to collect water in ditches on each side. Periodically, the water needs to be passed to the lower side of the roadway for transfer to a creek, stream, or other water body. There are a host of questions that come out of this very simple combination of issues, which include:
The answers to all of these depend on many factors and are the ones that are answered in the roadway design process. For most existing facilities, these are questions which can be answered by experience.After a washout, there is a tendency to get so focused on the most immediate and pressing issues of repair that the same mistakes are repeated. Often, a washed out culvert is replaced with another just like it! If the pipe was too small to pass this particular amount of water, isn’t it likely to encounter this same flow again soon?Why not spend the very few extra dollars by installing the next larger pipe size? It may also make sense to add another crossing pipe halfway uphill of the one that washed out. Between the two improvements, this may be sufficient to lessen future floods.
It’s important to note that there is no “one material fits all” answer. Each pipe material has benefits and shortcomings — and each should be considered when choosing pipes for culverts. One point to consider is that many regulating agencies forbid pipe smaller than fifteen inches in inside diameter. This provision has come about because of the tendency of smaller pipes to become clogged with large debris. Even though almost all of the products discussed will come in sizes much smaller, we do not recommend using pipes that are smaller than twelve inches under any circumstances.
The most common culvert material that we see is black corrugated pipe. It is made of a plastic called high-density polyethylene or HDPE. It’s comparatively inexpensive and light enough to handle without a lot of specialized equipment. In addition, it is chemically inert to the low pH associated with acid rain.
We encounter reinforced concrete and corrugated steel pipes equally often. For a number of reasons, though, we don’t see these products as frequently as the plastic pipe. If you have these products on site already and are considering replacing them, the new pipes should have properties similar to those described below. Both concrete and corrugated metal corrode — the HDPE pipe does not. In some ways, these materials provide a more forgiving installation than their HDPE cousins. That is, they tend to be a little stronger with shallow installations. In addition, the flexibility of HDPE allows the pipe to be installed without a constant grade (there could be a sag in the middle), whereas the concrete or metal pipes are more rigid.
In any case, the pipe you select should have:
If the pipe at your local hardware store doesn’t have these properties, consider asking them to stock it or finding a wholesale supplier and stocking it on site yourself. The success of your project will be largely dependent on how closely the installation instructions are followed. Pay particular attention to the recommendations regarding how the pipe trench is to be prepared, how the pipe is joined, and the technique for burying the pipe.
The main benefit of concrete is that it is a rigid surface that receives loads from above and spreads them across the entire structure. For proper service, it is especially important that the ground on which the concrete is placed is tightly compacted and well drained. Otherwise, the loads from above will not be uniformly transmitted to the ground below, and groundwater and frost will lift the slab. Both will cause the slab to break. PCC also requires the inclusion of reinforcing to handle certain internal stresses. How much steel, what kind, and the placement of the steel are all part of the design.
Consider one of the misnomers for the product, “blacktop.” If a camp has a soil roadway and decides to “black top” it, that’s what it will get — a road with a black top. However, without proper drainage and compaction beneath, the black topping will be stacked on the road edge after the first winter of plowing. Each granular layer beneath the asphalt concrete surface should be carefully compacted by power driven equipment until the rear tires of a fully loaded dump truck do not sink at all into the surface. Any material that moves under the weight of the truck should be dug out, replaced, recompacted, and retested.
This sequence will be more expensive than calling the local paving contractor and getting a blacktop quote, because laying asphalt is quick and easy with modern equipment. It’s the surface preparation, which is difficult and time consuming. This is one of those times when there’s no point in doing it at all if you’re not going to do it right. If the budget won’t allow you to do the whole project at once, phase it over several seasons and do what you can afford each year.
This “do-it-right-or-not-at-all” mindset especially applies if you already have an asphalt surface covered with cracks, the edges are breaking off, or humps appear during the winter. These are indications of poor under drainage. Just like a coat of paint won’t cure rot on a building, adding asphalt (or other “black stuff”) to the surface of the road won’t cure a failing roadway.
The drives in and out of your camp are the first and last things that your visitors encounter, so from a marketing standpoint, roadway access to your facility may be your most important site improvement. But there is certainly a happy medium between a concrete super-highway and a pothole-laden cart track. Capital cost has to be balanced against maintenance cost and lifespan of the roadway surface. Ask your engineer what’s available in your area and which products will best suit your operation.
Rick Stryker is a professional engineer with Camp Facilities Consulting providing study, design, permitting, and construction consultation services to the camp and conference center community. Camp personnel may contact him at 570-296-2765 or by e-mail at firstname.lastname@example.org .
Originally published in the 2003 March/April issue of Camping Magazine.